C7000 Specs

Rathbone Energy, an Authorized Cadex reseller, is proud to promote and sponsor Cadex Brand Battery Analyzers and all their products. In our efforts to promote and sell Cadex products, these Cadex, well written and fine web pages are copied to our site, (with minor modifications).

Special Value Priced Below Cadex Mfg. Reps!


Cadex 7200 2 independent stations for simultaneous service of 2 batteries; 100-240VAC, 50-60Hz; 1.5A max. line current Length: 312 mm (12.1"); Width: 240 mm (9.4"); Height: 90 mm (3.5"); Weight 3.2 kg (7.1 lb)		Cadex C7400 4 independent stations for simultaneous service of 4 batteries; 100-240VAC, 50-60Hz; 1.5A max. line current Length: 366 mm (14.4"); Width: 280 mm (11"); Height: 100 mm (3.8"); Weight 4.5 kg (10 lb) C7000 ER Specs

System:
User-programmable, adjustable from 1.2V to 15V; 100mAh to 24Ah; up to 4A charge and discharge current per station; 2A on digital discharge. The charge and discharge currents are automatically scaled to lower C-rates on batteries with higher than 4Ah; intelligent power management protects overload conditions; accommodates nickel-cadmium, nickel-metal-hydride, lead-acid and lithium-ion. Batteries are tested against preset parameters; short and reverse polarity protected; multiple redundant full-charge detection. Tamper proof through security system.

Adapters:
SnapLock Battery Adapters hold up to 10 C-Codes; C-Codes can be added, edited, copied to other adapters, locked, reset and erased with the analyzer's keypad.

Basic programs:

QuickTest - Checks battery state-of-health in 3 minutes. If outside testing range of 20-90% state-of-charge, a brief charge or discharge is applied.
Auto - Exercises battery and automatically applies Recondition if target capacity is not met. (Recondition only applies to nickel-based batteries)
Charge - Applies fast charge only; no capacity readings are taken.
Prime - Prepares new and stored batteries by cycling battery until the optimized capacity is reached.
Advanced programs:
SelfDCH - Measures self-discharge of battery; rest time in which measurement is taken is adjustable.
LifeCycle - Cycles battery until capacity drops to the user-set target. Keeps score of the cycle count.
DCHOnly - Discharges battery to the respective end-of-discharge voltage while measuring the capacity.
ExtPrime - Applies 16-hour trickle charge prior to Prime. Activates battery after extended storage.
OhmTest - Measures internal battery resistance through pulse method.
Boost - Wakes up batteries deactivated by excessive discharge. Energizes protection circuit on lithium-ion batteries. (Pressing station key for 2 seconds also activates Boost)
Q-Learn - Obtains QuickTest matrices when scanning a known good battery. Duration is 5minutes.
Learn - Improves QuickTest matrix by scanning batteries with various state-of-health conditions.
Custom1-4 - Sets 4 user-defined programs consisting of charge, discharge, rest periods and repeats.

Data Port:
RS-232 for DYMO LabelWriter SE300 to print battery labels; printer to produce service reports; or PC to run BatteryShop™ software. C7400 also features parallel port.
Firmware:
PC upgradeable, flash memory
Environmental:
Recommended operating temperature 0° to 45°C (32°F to 113°F);
storage temperature -40° to 75°C (-40°F to 167°F)
Approvals:
Tested and approved by ITS to comply with CSA/UL/CE standards
Warranty:
Cadex warrants against defective materials and workmanship for 3 years from purchase date.

Specifications for the Cadex C7000 ER Battery Analyzer

Cadex president and founder, Mr. Isidor Buchmann has written some of the very best information available about the use and care of battery packs. We have copied some of his articles to our web site. We have also provided direct links to Cadex articles on their web site.